Fraud Blocker

What should I do if my key won’t turn in the lock?

What should I do if my key won’t turn in the lock?

What should I do if my key won’t turn in the lock?

Knowledge Centre

Stop trying to force it – a forced key snaps, and then you have two problems. Check you have the right key, try your spare, relieve any pressure on the door, and give the cylinder a puff of the dry lubricant the lock manufacturer recommends (some specify graphite, others PTFE-based). If it is still stiff after that, the lock needs a locksmith, not more muscle.

A key that will not turn feels like an emergency, but the cause is often something simple, and most causes have simple fixes. Work through the checks below in order.

First: do not force it

Leaning on the key is the mistake to avoid: a key can snap off inside the cylinder. Then the door is still stuck and the broken piece has to come out before anything else can happen. Gentle wiggling is fine. Grunting is not.

The quick checks

Try the spare key. If the spare turns smoothly, your everyday key is likely worn – have a replacement cut before it fails completely.

Check it is the right key. Obvious, but on a bunch of similar keys it happens daily, especially in the dark or with gloves on.

Take the pressure off the door. On uPVC and composite doors especially, the door can sit under load – from its own weight, swelling in summer heat or shifting in cold weather, or a frame that has moved. Push the door firmly towards the frame, or lift it slightly by the handle, and try the key while holding it there. If it turns with the pressure off, the lock itself is probably fine and the door needs adjusting.

Lubricate the cylinder. A small puff of the dry lubricant the cylinder manufacturer recommends into the keyway, then work the key in and out gently a dozen times. Manufacturers differ: Yale and APECS specify a PTFE-based dry lubricant and advise against graphite for their cylinders, while other makers, such as Schlage, recommend graphite. Check the brand of your cylinder first. A dry lubricant is the right choice either way; ordinary oil sprays can leave a film that gathers dirt over time.

Wiggle, do not crank. Ease the key back a fraction of a millimetre and try turning with light finger pressure while jiggling gently. Worn internals sometimes catch at one exact depth.

What the symptoms usually mean

SymptomLikely causeThe fix
Spare key works, main key does notWorn keyNew key cut – lock is fine
Turns with pressure lifted off the doorDoor misalignmentHinge/keep adjustment
Stiff for both keys, gritty feelDry or dirty cylinderGraphite lubricant; strip and clean if it persists
Key will not go fully inDebris build-up, a broken key piece, or the wrong keyInspection – do not poke around with wire
Key turns but nothing happensInternal fault – cam or tailpieceLocksmith – mechanism or cylinder work
Gradually getting stiffer over monthsWear or a dropping doorInspection before it fails completely

These are pointers, not a diagnosis – the locksmith’s inspection is what confirms the actual cause.

When it is the door, not the lock

On uPVC and composite doors, a key that will not turn is frequently a door problem wearing a lock’s clothing. If you have to lift the handle before the key will turn, or the door has been getting stiffer through the seasons – freezing in winter months moves uPVC frames as surely as summer heat – the multipoint mechanism is probably fighting the frame rather than failing. That is adjustment work, and it is cheaper caught early.

What a locksmith will do

A proper visit starts with inspection, not drilling: which key, which way it fails, whether the door is under load, whether the cylinder or the mechanism is at fault. From there it might be lubrication and adjustment, a worn cylinder swapped out, or a mechanism repair. You should know the likely cause and the full price before work starts – say what the key does and does not do when you call, and the quote will be more accurate.

The price is agreed before anyone sets off, and work never starts until you have agreed it. AHLP advertises a 30-minute response, available every hour of every day.

Frequently asked questions

Can I use WD-40 in a lock?

It is the classic cupboard fix, but for a cylinder lock a graphite or PTFE dry lubricant is the better choice: it does the job without leaving an oily film that gathers grit and gums the pins up later. If WD-40 is all you have, the tiniest amount will free a lock for now – follow it with the right lubricant rather than re-dosing.

The key snapped while I was trying to turn it – now what?

Leave the lock alone and call. Do not try to dig the piece out with wire or tweezers – pushed deeper, it turns a simple extraction into a cylinder replacement. A locksmith removes the broken piece without damaging the lock where the lock allows it.

Is a key that will not turn an emergency?

If you cannot lock or unlock your property, treat it as urgent – a door you cannot secure is a security problem, and one you cannot open can become a safety one. If you have another working door and the stiff one is secure, it can wait for a normal appointment, but book it before it fails completely. Locks that are getting stiffer are on their way out.

Will I need a whole new lock?

Usually not. Many stiff-lock jobs end with lubrication, adjustment or a new cylinder, with the rest of the hardware left in place. The inspection shows which – and you will hear the price before anything is fitted.

Why did my key work fine yesterday and not today?

A lock rarely goes from perfect to dead overnight without a reason: a change in weather moving the door, a key that finally wore past its limit, or a mechanism part that gave up. The sudden ones are worth having looked at soon, because whatever gave way rarely fixes itself.

  1. HomeServe: How to fix common lock problems (homeserve.co.uk) https://www.homeserve.co.uk/knowledge-hub/home-maintenance-advice/how-to-fix-common-lock-problems/
  2. AHLP Knowledge Centre: Why won’t my uPVC door lock properly? (ahlp.co.uk) https://ahlp.co.uk/why-wont-my-upvc-door-lock-properly/
  3. AHLP Knowledge Centre: My key has snapped in the lock – do I need a replacement lock? (ahlp.co.uk) https://ahlp.co.uk/my-key-has-snapped-in-the-lock-do-i-need-a-replacement-lock/
  4. AHLP: locksmith services and published prices (ahlp.co.uk) https://ahlp.co.uk/locksmith-services/

Sources checked 28 October 2026; links re-verified 29 October 2026. Every lock and door is different – the inspection settles the cause, and the quote you agree before work starts is the price that matters.

Have questions or need support?
Reach out to us!
x